 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MICROWAVE CORPORATION v01.1002 HMC437MS8G SMT GaAs HBT MMIC DIVIDE-BY-3, DC - 7.0 GHz Features SSB Phase Noise: -153 dBc/Hz @100KHz Wide Bandwidth Output Power: -1 dBm Single DC Supply: +5V @ 69 mA MS8G SMT Package Typical Applications Prescaler for DC to C Band PLL Applications: * UNII, Pt. - Pt. & VSAT Radios * 802.11a & HiperLAN WLAN 10 FREQ. DIVIDER & DETECTORS - SMT * Fiber Optic * Cellular / 3G Infrastructure Functional Diagram General Description The HMC437MS8G is a low noise Divide-by-3 Static Divider utilizing InGaP GaAs HBT technology in a low cost 8 lead surface mount plastic package. This device operates from DC (with a square wave input) to 7.0 GHz input frequency from a single +5.0V DC supply. The low additive SSB phase noise of -153 dBc/Hz at 100 kHz offset helps the user maintain good system noise performance. Electrical Specifications, TA = +25 C, 50 Ohm System, Vcc= 5V Parameter Maximum Input Frequency Minimum Input Frequency Input Power Range Sine Wave Input [1] Fin= 1 to 6 GHz Fin= 6 to 7 GHz Output Power Reverse Leakage SSB Phase Noise (100 kHz offset) Output Transition Time Supply Current (Icc) Both RF Outputs Terminated Pin= 0 dBm, Fin= 6 GHz Pin= 0 dBm, Fout= 882 MHz -12 -10 -4 Conditions Min. 7.0 Typ. 7.5 0.1 -15 -15 -1 -50 -153 100 69 +12 +10 Max. Units GHz GHz dBm dBm dBm dBm dBc/Hz ps mA 1. Divider will operate down to DC for square-wave input signal. 10 - 90 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v01.1002 HMC437MS8G SMT GaAs HBT MMIC DIVIDE-BY-3, DC - 7.0 GHz GaAs MMIC SUB-HARMONICALLY Input Sensitivity Window17 Temperature PUMPED MIXER vs. - 25 GHz Input Sensitivity Window, T= 25 C 20 15 INPUT POWER (dBm) INPUT POWER (dBm) 20 15 10 5 0 -5 -10 -15 -20 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 INPUT FREQUENCY (GHz) INPUT FREQUENCY (GHz) Min Pin +25 C Max Pin +25 C Min Pin +85 C Max Pin +85 C Min Pin -40 C Max Pin -40 C 10 5 0 -5 -10 -15 -20 Recommended Operating Window 10 FREQ. DIVIDERS & DETECTORS - SMT 10 - 91 Output Power vs. Temperature 4 3 OUTPUT POWER (dBm) +25 C +85 C -40 C SSB Phase Noise Performance, Pin= 0 dBm, Fin= 6 GHz, T= 25 C 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 -170 2 10 2 1 0 -1 -2 -3 -4 -5 -6 0 1 2 3 4 5 6 7 SSB PHASE NOISE (dBc/Hz) 8 9 10 3 10 4 10 5 10 6 10 7 INPUT FREQUENCY (GHz) OFFSET FREQUENCY (Hz) Output Harmonic Content, Pin= 0 dBm, T= 25 C 0 Reverse Leakage, Pin= 0 dBm, T= 25 C 0 -10 Both Output Ports Terminated One Output Port Terminated -10 OUTPUT LEVEL (dBm) OUTPUT LEVEL (dBm) -20 -30 -40 -50 -60 -70 -20 -30 -40 Pfeedthru 2nd Harmonic -50 0 1 2 3 4 5 6 7 8 9 INPUT FREQUENCY (GHz) 0 1 2 3 4 5 6 7 8 9 INPUT FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v01.1002 HMC437MS8G SMT GaAs HBT MMIC DIVIDE-BY-3, DC - 7.0 GHz Output Voltage Waveform, Pin= 0 dBm, Fout= 882 MHz, T= 25 C 300 200 100 AMPLITUDE (mV) Absolute Maximum Ratings RF Input (Vcc= +5V) Vcc Maximum Channel Temperature Continuous Pdiss (T=85 C) (derate 9.85mW/C above 92 C) Storage Temperature Operating Temperature +13 dBm +5.5V 135 C 424mW -65 to +150 C -40 to +85 C 0 -100 -200 -300 10 FREQ. DIVIDER & DETECTORS - SMT -400 -500 22.5 DC blocking capacitors are required at RF input and RF output ports. Choose value for lowest frequency of operation. 23 23.5 24 TIME (ns) 24.5 25 25.5 Typical Supply Current vs. Vcc Vcc (V) 4.75 5.0 5.25 Icc (mA) 64 69 75 Note: Divider will operate over full voltage range shown above Outline Drawing NOTES: 1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED PLASTIC SILICA AND SILICON IMPREGNATED. 2. LEADFRAME MATERIAL: COPPER ALLOY 3. LEADFRAME PLATING: Sn/Pb SOLDER 4. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 5. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 6. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 7. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 10 - 92 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v01.1002 HMC437MS8G SMT GaAs HBT MMIC DIVIDE-BY-3, DC - 7.0 GHz Pin Description Pin Number 1 Function Vcc Description Supply voltage 5V 0.25V. Interface Schematic 10 2 IN RF input must be DC blocked. 3 IN RF input 180 out of phase with pin 2 for differential operation. AC ground for single ended operation. 4, 5 GND All ground leads and ground paddle must be soldered to PCB RF/DC ground. 6 OUT Divided output 180 out of phase with pin 7. 7 OUT Divided Output. 8 N/C No Connection For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 10 - 93 FREQ. DIVIDERS & DETECTORS - SMT MICROWAVE CORPORATION v01.1002 HMC437MS8G SMT GaAs HBT MMIC DIVIDE-BY-3, DC - 7.0 GHz Evaluation PCB 10 FREQ. DIVIDER & DETECTORS - SMT List of Materials Item J1 - J3 J4, J5 C1 - C4 C5 C6 U1 PCB* Description PC Mount SMA RF Connector DC Pin 100 pF Capacitor, 0402 Pkg. 10,000 pF Capacitor, 0603 Pkg. 4.7 F Tantalum Capacitor HMC437MS8G Divide-by-3 105697 Eval Board The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and backside ground slug should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. This evaluation board is designed for single ended input testing. J2 and J3 provide differential output signals. * Circuit Board Material: Rogers 4350 10 - 94 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v01.1002 HMC437MS8G SMT GaAs HBT MMIC DIVIDE-BY-3, DC - 7.0 GHz Application Circuit 10 FREQ. DIVIDERS & DETECTORS - SMT For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 10 - 95 |
Price & Availability of HMC437MS8G
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |